WEKO3
インデックスリンク
アイテム
高湿環境下における合成繊維・再生繊維集合体の圧縮クリープ特性
http://hdl.handle.net/10935/3263
http://hdl.handle.net/10935/32636f0fb821-5a96-423e-86f7-052a06d60e29
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
AA11482543V58N6PP89-97.pdf
|
|
| アイテムタイプ | default_学術雑誌論文 / Journal Article(1) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| タイトル | ||||||||||||
| タイトル | 高湿環境下における合成繊維・再生繊維集合体の圧縮クリープ特性 | |||||||||||
| 言語 | ja | |||||||||||
| 言語 | ||||||||||||
| 言語 | jpn | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| 主題Scheme | Other | |||||||||||
| 主題 | Compression creep | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| 主題Scheme | Other | |||||||||||
| 主題 | Fiber assembly | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| 主題Scheme | Other | |||||||||||
| 主題 | High humidity | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| 主題Scheme | Other | |||||||||||
| 主題 | Regenerated fiber | |||||||||||
| キーワード | ||||||||||||
| 言語 | en | |||||||||||
| 主題Scheme | Other | |||||||||||
| 主題 | Synthetic fiber | |||||||||||
| 資源タイプ | ||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||
| 資源タイプ | journal article | |||||||||||
| その他（別言語等）のタイトル | ||||||||||||
| その他のタイトル | Compressive Creep Properties of Synthetic Fiber and Regenerated Fiber Assemblies under High Humidity Environment | |||||||||||
| 言語 | en | |||||||||||
| 著者 |
中島,千恵
× 中島,千恵
× 米田,守宏 |
|||||||||||
| 抄録 | ||||||||||||
| 内容記述タイプ | Abstract | |||||||||||
| 内容記述 | In this study, acompression creep behavior of three-dimensional fiber assembly for futon wadding use is investigated under high humidity condition, which simulates sleeping microclimate condition. Compression creep tester is used for the measurement, and humid air is supplied to the tester with high humidity air generator. Samples used are twelve kinds of staple fiber made of polyester (PET) fiber with round, W-shaped and hollow section, polytrimethyleneterephtalate (PTT) fiber, cupra-ammonium (cupra) fiber and Lyocell fiber. Results are obtained as follows. (1)Compression creep deformation ratio of regenerated fiber assembly is significantly large compared to that of synthetic fiber assembly for high and low stress. (2)The order of creep deformation ratio for the same fineness and fiber diameter is as follows. Cupra is the largest, PET with round section follows and PET with w-shaped section is the smallest for fineness of 1.4 dtex and fiber length of 38 mm. PET with hollow section is larger than PET with round section for 6.6 dtex and 51 mm (3)There is no significant diference in compression creep deformation ratio for staple fiber assembly made of same fiber material of which fineness ranges 1.3-6. dtex and fiber length ranges 38-51 mm. (4)Compression creep defomation ratio in high stress condition (2156 Pa) is larger than that of low stress condition (1176Pa). (5)Compression creep behavior of staple fiber in high humidity condition is expressed as following equation. Є_t=Y_0 1n(vt+1) where,Y_0 and v are constants derived from measurement curve. (6)Y_0 is the magnitude of compression creep at a certain time, and V_ini(=Y_0･v) is the initial tangential rate of creep. Parameters Y_0 and V_ini is useful for describing compression creep behavior of synthetic and regenerated fiber assembly. | |||||||||||
| 言語 | en | |||||||||||
| 内容記述 | ||||||||||||
| 内容記述タイプ | Other | |||||||||||
| 内容記述 | (C)2012 The Textile Machinery Society of Japan | |||||||||||
| 言語 | en | |||||||||||
| 書誌情報 |
en : Journal of Textile Engineering 巻 58, 号 6, p. 89-97, 発行日 2012-10 |
|||||||||||
| 出版者 | ||||||||||||
| 出版者 | 日本繊維機械学会 | |||||||||||
| 言語 | ja | |||||||||||
| ISSN | ||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||
| 収録物識別子 | 1346-8235 | |||||||||||
| 書誌レコードID | ||||||||||||
| 識別子タイプ | NCID | |||||||||||
| 関連識別子 | AA11482543 | |||||||||||
| 著者版フラグ | ||||||||||||
| 出版タイプ | VoR | |||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||
